Land Drilling Engines and Generator Sets
C18 ACERT Land Mechanical Drilling Engine
-
Minimum Rating575.0 bhp
-
Maximum Rating700 BHP
-
Maximum Rating800.0 bhp
-
EmissionsEPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Engine Specifications
- Minimum Rating
- 575.0 bhp
- Maximum Rating
- 700 BHP
- Maximum Rating
- 800.0 bhp
- Emissions
- EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Emissions
- EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Displacement
- 1100 in³
- Rated Speed
- 2100.0 RPM
- Minimum Rating
- 575 BHP
- Bore
- 5.71 in
- Bore
- 5.7 in
- Stroke
- 7.2 in
- Stroke
- 7.2 in
- Displacement
- 1100.0 in3
- Rated Speed
- 2100 r/min
- Aspiration
- Turbocharged-Aftercooled
- Aspiration
- Turbocharged-Aftercooled
- Governor and Protection
- ADEM A3
- Engine Weight
- 2807.0 lb
- Engine Weight
- 2807 lb
- Oil Change Interval
- 250
- Rotation
- Counterclockwise
- Oil Change Interval
- 250
- Rotation from Flywheel End
- Counterclockwise
- Flywheel and Flywheel Housing
- SAE No. 0 or SAE No. 1
- Flywheel and Flywheel Housing
- SAE No. 0 or SAE No. 1
- Flywheel Teeth
- 136 (SAE 0), 113 (SAE 1)
- Flywheel Teeth
- 136 (SAE 0), 113 (SAE 1)
Capacity for Liquids
- Minimum Cooling System
- 13.2 gal (US)
Dimensions
- Length
- 54.7 in
- Length
- 54.7 in
- Width
- 36.2 in
- Width
- 36.2 in
- Height
- 49.5 in
- Height
- 49.5 in
-
Air Inlet System
- Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
- Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection
-
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature,pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
-
Cooling System
- Thermostats and housing — outlet vertical
- Jacket water pump — gear-driven, centrifuga
- RH front water pump inlet
- All plugs/fittings are STOR for lines gp water
-
Exhaust System
- Exhaust manifold — dry
- Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
- Dual turbo — exhaust elbow, dry 203 mm (8 in)
-
Flywheels and Flywheel Housings
- See Mandatory Options
-
Fuel System
- Electronic unit injector
- Fuel filter, secondary, mid-mount (LH 2 micron high performance)
- Fuel transfer pump, LH front
- Fuel priming pump, LH mid-mount
- Fuel sample valve, mounted on fuel filter base.
-
Lube System
- Crankcase breather — rear valve cover
- Oil cooler — RH (dual)
- Oil filter — RH, LH
- Oil pan — front sump
- Oil dipstick — LH front
- Oil pump
-
Mounting System
- Front support (shipping only)
-
Power Take-Offs
- Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
- Hydraulic pump drive, SAE A, 11-tooth
-
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins,sockets)
-
Mandatory Options
- Throttle position sensor
- Single turbo only — exhaust system (front or rear)
- Flywheel housing or rear PTO
- Primary filter/water separator
-
Air Compressor
- Air compressor governor
- Expansion chambers
-
Air Inlet System
- Air cleaners
- Air lines
-
Charging System
- Charging alternators
- Alternator mountings
- Alternator wiring
- Circuit breakers and mountings
- Alternator belt guard
-
Cooling System
- Radiator
- Fan drive with radiator packages
- Fan height instructions
- Vee belts
- Aftercooler lines with Caterpillar installed radiator
- Single turbo configuration rear-facing exhaust
- Single turbo configuration rear-facing exhaust
- Aftercoooler lines
- Suction fan adapters
- Blower fan adapter
- Blower fan
- Suction fan
- Fan belt
- Coolant level sensor
- Dry charge coolant conditioners
-
Exhaust System
- Turbo exhaust connection
- Flexible fittings
- Elbows, flange, clamp, pipes
- Exhaust adapters
- Manifold
- Mufflers
-
Fuel Systems
- Flexible fuel lines
- Fuel filter location
- Fuel cooler
- Water separator
-
Instrumentation
- Gauges and instrument panels
-
Lube System
- Oil pans
- Drain and cover
- Oil level gauge
- Remote oil filters
- Oil filters
- Lubricating oils
-
Mounting System
- Structural steel base
- Front and rear engine support
-
Power Take-Offs
- Rear enclosed clutches
- Hydraulic pump drives
- Hydraulics gear pumps
- Clutch supports
- Crankshaft pulleys
-
Protection System
- Air shutoff
-
Starting System
- Air starting motors
- Air pressure regulator
- Air silencer
- Start switch
- Electric starting motors — 12V, 24V
- Battery sets – 24V
- Battery cable and rack
- Starting aids
-
Transmission Arrangement
- Transmission water lines