New Cat 907 Compact Wheel Loader for Sale

Cat 907 Compact Wheel Loader

Maximum Gross Power

74.7 hp
Engine Model

Cat C2.8*
Maximum Engine Speed

2550 rpm
Maximum Gross Power

2400 r/min

Engine

Maximum Gross Power: 74.7 hp
Engine Model: Cat C2.8*
Maximum Engine Speed: 2550 rpm
Maximum Gross Power: 2400 r/min
Maximum Gross Power: 74.7 hp
Maximum Gross Power: 74.3 hp
Maximum Gross Power: 75.3 mhp
Rated Net Power: 2400 r/min
Rated Net Power: 72.7 hp
Rated Net Power: 72.1 hp
Rated Net Power: 73.1 mhp
Maximum Gross Torque: 222 lb/ft
Maximum Gross Torque: 221 lb/ft
Maximum Net Torque: 218 lb/ft
Maximum Net Torque: 217 lb/ft
Displacement: 171 in³
Bore: 3.54 in
Stroke: 4.33 in
Note: *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Note: Advertised power is tested per the specified standard in effect at the time of manufacture.
Note: Net power advertised is the power available at the flywheel.
Note: #Maximum gross and net torque measured at 1,600 rpm.

Weights

Operating Weight: 12765 lb

Buckets

Bucket Capacities: 0.75-1.55 m³ (1.0-2.0 yd³)
Bucket Capacities: 0.80-1.35 m³ (1.0-1.7 yd³)
Bucket Capacities: 1.25-1.55 m³ (1.6-2.0 yd³)
Multi: 0.75-1.1 m³ (1.0-1.4 yd³)
Note: Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
Note: Bucket capacities stated include BOCE, in line with ISO 7546.

Service Refill Capacities

Fuel Tank: 24 Gal
Cooling System: 3.2 Gal
Engine Crankcase: 2.3 Gal
Axles: 2.3 Gal
Axles: 2.3 Gal
Hydraulic System: 17.8 Gal
Hydraulic Tank: 11.8 Gal
Transmission: 0.6 Gal
Note: No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.

Axles

Front: Fixed (standard), Locking Differential (optional)
Rear: Fixed (standard), Locking Differential (optional)
Note: Oscillation of ±11 degrees via hitch between front and rear frames.

Steering

Steering Articulation Angle: 39 °
Maximum Flow: 12.3 gal/min
Maximum Working Pressure: 3336 psi
Steering Cycle Times: 2.8 s
Number of Steering Wheel Turns: 3.25 turns or 4.00 turns

Transmission

Forward and Reverse: 6 mile/h
Forward and Reverse: 6 mile/h
Forward and Reverse: 10.5 mile/h
Forward and Reverse: 12 mile/h
Forward and Reverse: 25 mile/h
Note: #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).
Note: *Creep function not available in this gear or above.
Note: **Max speed dependent on model and configuration (standard vs. high speed transmission).
Note: ***Reverse is 30 km/h (19 mph).

Tires

Tire Size: *405/70 R18 SPT9
Tire Size: 405/70 R18 Powerloads
Tire Size: 340/80 R18 XMCL/Bibload
Tire Size: 340/80 R18 TRI 2
Tire Size: 40X14-20 TL, SM/TR
Tire Size: 340/80 R18 Duraforce
Note: *This tire has been used for all dimension, stability and performance data.
Note: Other tire choices are available. Contact your Cat dealer for details.
Note: Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Note: Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.

Cab

ROPS: ISO 3471:2008
FOPS: ISO 3449:2005 Level II
Note: Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.
Note: The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A).
Note: *Measurements were conducted with the cab doors and windows closed.
Note: The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available.

Loader Hydraulic System

Main Relief: 3408 psi
Main Relief: 21 gal/min
Main Relief: 32 gal/min
Main Relief: 3408 psi
Main Relief: 12 gal/min
Hydraulic Cycle Time: 2.2 s
Hydraulic Cycle Time: 5 s
Hydraulic Cycle Time: 1.6 s
Hydraulic Cycle Time: 2.8 s
Note: * Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.

Dimensions - With HPL-V Coupler - Approximate#

Height: 8.5 ft
Height: 9.08 ft
Height: 1.58 ft
Height: 1 ft
Length: 17.58 ft
Length: 4.58 ft
Length: 3.58 ft
Length: 7.08 ft
Length: 3.5 ft
Clearance: 8.25 ft
Clearance: 9.5 ft
Clearance: 9.92 ft
Height: 10.67 ft
Height: 13.5 ft
Reach: 2.33 ft
Carry Height: 1.08 ft
Dig Depth: 0.33 in
Width: 6.75 ft
Width: 4.67 ft
Turning Radius: 14.75 ft
Width: 6.07 ft
Turning Radius: 12.92 ft
Turning Radius: 6.75 ft
Rack Angle at Full Lift: 56°
Dump Angle at Full Lift: 45°
Rack Angle at Carry: 51°
Departure Angle: 30°
Articulation Angle: 39°
Operating Weight: 12689 lb
Tipping Load: 9773 lb
Tipping Load: 8235 lb
Operating Weight: 12220 lb
Tipping Load: 7807 lb
Tipping Load: 6569 lb
80: 5255 lb
Note: *Vary with bucket
Note: **Vary with tire
Note: ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.
Note: ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note: †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note: ††Full compliance to EN474-3 and SAE J1197.
Note: #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note: Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II
Note: Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Dimensions - With SSL Coupler - Approximate

Height: 8.5 ft
Height: 9.08 ft
Height: 1.58 ft
Height: 1 ft
Length: 18.17 ft
Length: 4.58 ft
Length: 3.58 ft
Length: 7.08 ft
Length: 4.33 ft
Clearance: 7.83 ft
Clearance: 9.5 ft
Clearance: 9.92 ft
Height: 10.67 ft
Height: 13.83 ft
Reach: 2.67 ft
Carry Height: 1.17 ft
Dig Depth: 3 in
Width: 6.75 ft
Width: 4.67 ft
Turning Radius: 15 ft
Width: 6.08 ft
Turning Radius: 12.92 ft
Turning Radius: 6.75 ft
Rack Angle at Full Lift: 51°
Dump Angle at Full Lift: 50°
Rack Angle at Carry: 46°
Departure Angle: 30°
Articulation Angle: 39°
Operating Weight: 12897 lb
Tipping Load: 8653 lb
Tipping Load: 7257 lb
Operating Weight: 12414 lb
Tipping Load: 7416 lb
Tipping Load: 6266 lb
80: 5013 lb
Note: *Vary with bucket
Note: **Vary with tire
Note: ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.
Note: ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note: †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note: ††Full compliance to EN474-3 and SAE J1197.
Note: #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note: Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II
Note: Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Sustainability

Recyclability: 93%

OTHER
- Fenders, front and rear
- Loader arm safety brace
- Lockable, fuel cap, HVAC filters, nose cone
- Ground level easy access daily service points
- Machine lifting/tie down points
- Scheduled Oil Sampling (S·O·S SM) ports, engine oil and hydraulic oil
- Recovery hitch with pin
- Paint, Electro-Coat primer, gloss topcoat
- Lockable main and side engine enclosures
HYDRAULICS
- Dead engine lower, lift valve, manual
- Hydraulic pilot shut off switch, in cab
- Hystat displacement pump, infinitely variable
- Motor, single drive with dedicated implement and steering pumps
- Electro-hydraulic, fully proportional controls
- Demand cooling fan, hydraulically driven
- Caterpillar HYDO^™ Advanced 10 hydraulic oil
- Implement valve, pressure compensated
- Joystick, single lever, single auxiliary roller
- Coupler/pin on attachment ready
- Multi-function lift and tilt with loader arm float
ELECTRICAL
- Lights, roading, front halogen
- Alternator, 100 amp sealed
- Service (Electronic Technician^™)
- Lights, rear stop and turn, LED
- Battery, heavy duty, 12V, 90Ah and 1,000 CCA
- Product Link^™
- Cab mounted fuse panel
- Battery disconnect switch
POWER TRAIN
- Axles, heavy duty, frame mounted with outboard planetary reduction
- Closed circuit breather Coolant, extended life, –36° C (–33° F)
- Fuel pump, priming (manual)/water separator/drain
- Air cleaner, two stage filter, with in cab audio/visual indicator on display
- Cat C2.8 engine
  –Diesel particulate filter (Fit for Life)
  –Fuel, diesel, ultra low or low Sulphur
  –Hydrostatic transmission, two speed, with inching function, “shift on the go”
  –Power train mode, hystat
- U.S. EPA Tier 4 Final and EU Stage V emissions compliant
- Drive shaft, sealed for life, universal joints Engine, auto idle shutdown, hibernation mode
- Engine oil, ECO drain tap and hose
OPERATOR ENVIRONMENT
- Cab
  –Doors (2), fixed glass
  –Wipers, front and rear, full front coverage
  –Windshield, front single piece
  –Window, rear heated
  –Radio ready, speakers and wiring
  –Air vents, (4) screen, (7) directional
  –Heating, mechanical control unit
  –Sun visor, solid, front full width
  –Interior light (incandescent)
- Joystick, seat mounted, standard multifunction
  –FNR, auxiliary roller, speed range select, continuous flow, differential lock, horn
  –Arm rest, padded right, multiple position vertical height
- Seat, manual height adjustment, (cab) fabric with adjustable left arm rest, (canopy) vinyl
- ROPS/FOPS certified canopy/cab
  –12V power outlets, interior/exterior
  –Pedals, raised, foot, brake/inching, accelerator
  –Lever, parking brake
  –Cup holders (2)
  –CB radio clip, phone holder
  –Door release, internal (left and right)
  –Hook, large, coat and hard hat
  –Floormat, heavy duty, easy clean
  –Mirrors, (2) external breakaway, (1) internal
  –Operator station on isolation mounts
  –Steering wheel, spinner knob, horn in center
  –Seat belt, orange, retractable, 51 mm (2 in)
  –Storage, personal (trays [3], seat pocket)
  –Steering column, tilt adjusted
  –Column mounted multi function control: lights, roading, wipers, self canceling turn signals
  –Quick coupler switch, in cab
- Display, analog and digital
  –Gauges (2), hydraulic oil, engine coolant
  –Digital with soft touch buttons – fuel level, speed range, speedometer, service hour meter, service/maintenance information, hydraulic and power train performance and aggressiveness settings, security passcode (multiple languages)

OPERATOR STATION
- Seat belt options, multiple
- Interior light, door activated
- Joystick, FNR, twin auxiliary roller, differential lock, horn
- Mirrors (2) electronically adjustable, heated external, plus lower parabolic mirror
- Radio, FM or digital audio broadcast
- USB ports (2), interior
- Air Conditioning, automatic temperature control (ATC)
- Secondary display, front or rear view camera
- Soft touch keypad options, 8 or 16 button
- Sun visor, rear perforated
- Seat packages; deluxe or premium
- Doors, sliding windows (left and right)
- Phone holder, spring loaded
- Storage, lockable box or lockable cooled box
POWER TRAIN
- Creep and throttle lock function
- Fuel pump, priming, manual
- Cold start – jacket water heater, bypass valve
- Power train mode, utility (includes keypad)
- 40 km/h (25 mph) hydrostatic transmission, 3-speed, “shift on the go”, secondary steering and boosted brakes
- Antifreeze, extended life coolant, –50° C (–58° F)
HYDRAULICS
- Caterpillar Bio HYDO Advanced hydraulic oil
- Auxiliary flow, single standard (3) valve, single high flow (3) valve, dual high flow (4) valve
- Reversing fan
- Quick disconnect auxiliary hydraulics
- Ride Control or load check valves
- Connect under pressure and case drain
ELECTRICAL
- Push to start
- Work tool wiring harness, (3) in cab switches
- Lighting packages, multiple; front, rear, engine bay (LED or HAL)
OTHER
- Rotary sensors (snubbing, kickouts, parallel)
- Couplers, vertical (SSL), horizontal (HPL-V, HPL-A)