Auxiliary Engines
Cat C32 Auxiliary / Diesel Electric Propulsion Engine (IMO III)
-
Power Range781 - 1047
-
Frequency50 / 60
-
EmissionsIMO II, IMO III U.S. EPA T4, EU Stage V and China-II
-
Minimum Rating1047 BHP
Power Rating
- Power Range
- 781 - 1047
- Minimum Rating
- 1047 BHP
- Maximum Rating
- 1332 BHP
Generator Set Specifications
- Frequency
- 50 / 60
Engine Specifications
- Emissions
- IMO II, IMO III U.S. EPA T4, EU Stage V and China-II
- Aspiration
- Turbocharged- Aftercooled
- Bore
- 5.71 in
- Configuration
- V 12, 4-stroke-cycle diesel
- Displacement
- 1959 in³
- Rotation
- Counterclockwise
- Stroke
- 6.38 in
- Rated Engine Speed
- 1500 /1800 rpm
- Cooling
- Heat exchanger or keel cooled
- Flywheel Housing
- SAE No. 0 with SAE No. 18 flywheel (136 teeth)
- Governor
- Electronic (A5 ECM)
- Oil Change Interval
- 750 hrs - deep pan
- Refill Capacity
- Lube Oil System w/ oil filter change: 146 L (38.5 gal) - deep pan
Dimensions & Weights
- Maximum Engine Dry Weight
- 7160 lb
- Maximum Height
- 63.5 in
- Maximum Length
- 89.8 in
- Maximum Width
- 57.3 in
- Minimum Engine Dry Weight
- 6950 lb
- Minimum Height
- 59.3 in
- Minimum Length
- 83.9 in
- Minimum Width
- 57.1 in
Clean Emissions Module (CEM) - Dimensions
- 6 Brick U
- 23.5 in
- 6 Brick U
- 85 in
- 6 Brick U
- 1235 lb
- 6 Brick U
- 56.9 in
- 6 Brick Z
- 23.5 in
- 6 Brick Z
- 147.7 in
- 6 Brick Z
- 1246 lb
- 6 Brick Z
- 43.5 in
- Dosing Cabinet
- 22.8 in
- Dosing Cabinet
- 37.4 in
- Dosing Cabinet
- 209 lb
- Dosing Cabinet
- 18.8 in
-
AIR INLET SYSTEM
- Separate circuit aftercooled (SCAC)
- Closed crankcase fumes disposal
-
CONTROL SYSTEM
- 24V control system
-
COOLING SYSTEM
- Heat exchanger or Keel Cooling
- Watercooled exhaust manifold and turbocharger
- Hard seawater lines – no flexible hoses
- Flanges for cooling connections, ANSI or DIN
-
FUEL SYSTEM
- Duplex fuel filters with hybrid fuel lines
- Shipped loose primary fuel filter with water separator
- Fuel transfer and priming pump
-
LUBE SYSTEM
- Oil fill, simplex filter and dipstick
- Deep or shallow sump oil pan
-
MOUNTING SYSTEM
- Adjustable front support mounting system
-
GENERAL
- Right or left hand service sides
- Customer wiring and service tool connector
-
ALARM AND PROTECTION
- MECP I control panel
- MECP III control panel with Cat® Alarm and Protection System
-
EXHAUST SYSTEM
- Water-in-fuel and exhaust temperature sensors
- Muffler
-
CHARGING SYSTEM
- Charging alternator
-
FUEL SYSTEM
- Manual or electric fuel priming pump
- Fuel cooler
-
LUBE SYSTEM
- Duplex oil filters
-
POWER TAKE-OFFS
- Front drives including stub shaft and pump drive
- Rear SAE A or B pump drives
-
STARTING SYSTEM
- Starting motors – air, electric or redundant