New Cat?� C18 Diesel Fire Pump for Sale

Cat^?� C18 Diesel Fire Pump

Minimum Power

600.0 bhp
Maximum Power

800 hp
Maximum Power

800.0 bhp
Rated Speed

1500-2100 rpm

Power Rating

Minimum Power: 600.0 bhp
Maximum Power: 800 hp
Maximum Power: 800.0 bhp
Rated Speed: 1500-2100 rpm
Minimum Power: 600 hp
Rated Speed: 1500-2100 rpm

Emission Standards

Emissions: U.S. EPA Tier 3, Tier 2 or Non-certified emission standards for stationary emergency fire pump engines. FM Approved, UL Listed
Emissions: U.S. EPA Tier 3, Tier 2 or Non-certified emission standards for stationary emergency fire pump engines. FM Approved, UL Listed

General

Engine Configuration: Inline 6, 4-Stroke-Cycle Diesel
Bore: 5.7 in
Bore: 145 mm (5.71 in)
Stroke: 7.2 in
Displacement: 1104.5 in³
Stroke: 183 mm (7.2 in)
Compression Ratio: 16.3:1
Aspiration: Turbocharged Aftercooled (TA)
Displacement: 18.1 L (1104.53 in³)
Aspiration: Turbocharged Aftercooled (TA)
Rotation from Flywheel End: Counterclockwise
Compression Ratio: 16.3:1
Aftertreatment: -
Rotation: Counterclockwise

Engine Dimensions - Approximate

Length: 74.7 in
Width: 42.6 in
Height: 54.3 in
Weight: 4306 lb
Width: 1081.7 mm (42.6 in)
Height: 1379.6 mm (54.3 in)
Length: 1889 mm (74.37 in)
Weight: 1953 kg (4306 lb)

Air Inlet System
- Dual turbocharger: front and rear inlet 127.mm (5.0 in)
- Separate Circuit Aftercooled (SCAC)
- Optional Air Cleaner - dual element, installed
Charging System
- Charging alternator 24 volt, 50 amp
Control System
- Dual Electronic Control Units (ECU), primary and secondary with auto switching capability
- Electronic governing, PTO speed control
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and top engine limit
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speeds, temperature, pressure)
- SAE J1939 broadcast (diagnostic, engine status, and control)
Cooling System
- Thermostats and housing, vertical outlet
- Jacket water pump, gear driven, centrifugal
- Heat exchanger installed
- Expansion tank
- FM Required Raw Water Cooling Loops: 1.5" iron, horizontal or vertical, 1.5" 316 stainless steel, horizontal or vertical, 2" iron, horizontal or vertical (2100 rated rpm only), or 2" 316 stainless steel, horizontal or vertical (2100 rated rpm only)
Exhaust System
- Exhaust manifold, dry
- Dual turbo: exhaust elbow, dry 203 mm (8 in)
Flywheels and Flywheel Housing
- SAE No. 1 flywheel
- SAE No. 1 flywheel housing
- SAE standard rotation
Fuel System
- Electronic unit injector
- Fuel filter, secondary (2 micron)
- Fuel transfer pump
- Fuel sample valve, mounted on fuel filter base
- Primary fuel filter / water separator
Instrumentation
- Digital Display mounted in Junction Box, LH side of engine. Displays: Oil pressure, Fuel pressure, Charging voltage, Coolant temperature, Raw water temperature, and Engine hours
Lube System
- Crankcase breather, front valve cover
- Oil cooler
- Lube oil filter
- Front sump oil pan
- Oil filler
- Oil dipstick
- Oil pump
Mounting System
- Front and rear support
Power Take-Offs
- Flywheel stub shaft
Protection System
- Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
Starting System
- 24 volt, LH electric starting motor
- Jacket water heater (3 kW, 120-240 volt)
General
- Vibration damper and guard
- Lifting eyes
- Automatic variable timing, electronic
- Paint - fire pump red