New G3408C Low Emissions Gas Compression Engine for Sale

G3408C Low Emissions Gas Compression Engine

Engine Specifications

Minimum Rating: 425.0 bhp
Maximum Rating: 425 BHP
Maximum Rating: 425.0 bhp
Emissions: NSPS Site Compliant Capable or Non-regulated
Emissions: NSPS Site Compliant Capable with Customer-provided SCR Aftertreatment
Displacement: 1099.0 in3
Minimum Rating: 425 BHP
Compression Ratio: 8.5:1
Compression Ratio: 8.5:1
Aspiration: Turbocharged-Aftercooled
Aspiration: Turbocharged-Aftercooled
Rotation: Counterclockwise
Rotation from Flywheel End: Counterclockwise
Flywheel and Flywheel Housing: SAE No. 0
Flywheel and Flywheel Housing: SAE No. 0
Flywheel Teeth: 136
Flywheel Teeth: 136
Oil Change Interval: 750 hours
Oil Change Interval: 750 hours
Ignition: Cat EIS
Stroke: 6.0 in
Stroke: 6 in
Bore: 5.4 in
Bore: 5.4 in
Displacement: 1099 in³
Length: 69.1 in
Width: 61.5 in
Height: 69.2 in
Weight: 2041 lb

Capacity for Liquids

Air Inlet System
- Air cleaner — single element with service indicator
Control System
- Electronic governor
- Air/fuel ratio control
Cooling System
- Thermostats and housing
- Jacket water pump
- Aftercooler water pump
- Aftercooler core
Exhaust System
- Watercooled exhaust manifolds
- Dry exhaust elbow
Flywheel & Flywheel Housing
- SAE No. 0 flywheel
- SAE No. 0 flywheel housing
- SAE standard rotation
Fuel System
- Gas pressure regulator (1.5 to 5 psi gas supply required)
- Natural gas carburetor
Ignition System
- Cat Electronic Ignition System (EIS) with detonation sensitive timing
Instrumentation
- Service meter
Lube System
- Crankcase breather — top mounted
- Oil cooler
- Oil filter — RH
- Oil pan — deep sump
- Oil filler — RH in valve cover and RH dipstick
Mounting System
- Engine supports
Protection System
- Detonation sensitive timing control
- Shutoff
General
- Paint — Cat yellow
- Crankshaft vibration damper and pulleys
- Lifting eyes
- Cylinder block inspection covers

Air Inlet System
- Air cleaner — two-stage
- Air inlet adapter
- Precleaner
- Air cleaner rain cap
Charging System
- Battery chargers
- Charging alternators
- Ammeter gauge
- Ammeter gauge and wiring
- Control mounting
Cooling System
- Radiators
- Blower fan and fan drives for customer suppliedradiators
- Expansion tank
- Heat exchangers
Exhaust System
- Flexible fittings
- Elbows
- Flanges
- Rain caps
- Mufflers
- Exhaust manifold — instrument holes at each port
Fuel System
- Dual gas regulator
- Carburetor kits
- Fuel filter
Ignition System
- CSA ignition
- Ignition ground wiring harness
- Power supply
Instrumentation
- Alarm module
- Gauges and instrument panels
Mounting System
- Vibration isolators
Power Take-offs
- Auxiliary drive pulleys
- Enclosed clutch and clutch support
- Front stub shaft
- Flywheel stub shaft
- Pulley removal
Protection System
- Gas valves
- Status control box interconnect wiring harness
Starting System
- Air starting motor
- Air pressure regulator
- Air silencer
- Electric start control
- Electric starting motors — single 24V
- Starting aids
- Battery sets — (24V dry), cables, and rack
General
- Special paint