Industrial
Cat?� C1.5 Diesel Engine
-
Maximum Power24.6 hp
-
Maximum Torque63.4 lb-ft @ 1800 rpm
-
Rated Speed2200/2800 rpm
-
Minimum Power24.6 hp
Power Rating
- Maximum Power
- 24.6 hp
- Maximum Torque
- 63.4 lb-ft @ 1800 rpm
- Rated Speed
- 2200/2800 rpm
- Minimum Power
- 24.6 hp
Emission Standards
- Emissions
- U.S. EPA Tier 4 Final
General
- Engine Configuration
- In-Line 3, 4-Stroke-Cycle Diesel
- Engine Configuration
- In-Line 3
- Bore
- 3.3 in
- Stroke
- 3.5 in
- Bore
- 84 mm (3.3 in)
- Displacement
- 91 in³
- Compression Ratio
- 22.5:1
- Stroke
- 90 mm (3.5 in)
- Aspiration
- Naturally Aspirated (NA)
- Combustion System
- Indirect Injection
- Displacement
- 1.496 L (91 in³)
- Rotation from Flywheel End
- Counterclockwise
- Aftertreatment
- -
- Cooling System Capacity
- 2.6 L (2.75 qt)
- Cooling System
- 2.6 L (2.75 qt)
- Lube System
- 6 L (6.3 qt)
- Lube System
- 6 L (6.3 qt)
Engine Dimensions - Approximate
- Length
- 22.5 in
- Width
- 17.9 in
- Height
- 25.3 in
- Weight
- 327 lb
- Height
- 643 mm (25.3 in)
- Length
- 572 mm (22.5 in)
- Weight
- 148 kg (327 lb)
- Width
- 453 mm (17.9 in)
Engine Dimensions (Approximate. Final dimensions dependent on selected options)
- Length
- 572 mm (22.5 in)
- Width
- 453-512 mm (17.8-20.2 in)
- Height
- 643 mm (25.3 in)
- Weight
- 149-156.5 kg (328.5-345 lb)
Aftertreatment Dimensions (Approximate. Final dimensions dependent on selected options)
- Length
- 449 mm, 17.6 in (Tier 4 Final only)
- Weight
- 13 kg (28.7 lb) (Tier 4 Final, >19 kW/25 hp only)
- Diameter
- 170 mm (6.7 in) (Tier 4 Final only)
Aftertreatment Dimensions - Approximate
- Diameter
- 170 mm (6.7 in)
- Length
- 449 mm, 17.6 in
- Weight
- 13 kg (28.7 lb) (Tier 4 Final, >19 kW/25 hp only)
-
Air Inlet System
- Inlet manifold with choice of inlets.
-
Control System
- Alternator 12 volt 65 amp
- Starter motor 12 volt
- Glow plug starting aid
- Tier 4 Final: Alternator 12V 85 amp
-
Cooling System
- Belt-driven coolant pump
- Coolant temperature switch
- Choice of cooling fans
-
Flywheel & Flywheel Housing
- Naturally Aspirated: SAE No. 7 1/2 flywheel
- Naturally Aspirated: Choice of SAE No. 4 or standard backplate flywheel housing
-
Fuel System
- Fuel injection pump
- Spin-on fuel filter
- Electronic Shut-off Solenoid (ESOS)
-
Lube System
- Alternative oil fillers
- Spin-on lube oil filter
- Lube oil pressure switch
- Lube oil sump
-
Power Take Off (PTO)
- Provision for Power Take Off (PTO)
-
General
- Cast iron, engine block
- Cast iron exhaust manifold--side outlet
- Cold start capability to -20° C (-4° F)
- Gradeability 35° continuous