New C15 ACERT Land Mechanical Drilling Engine for Sale

C15 ACERT Land Mechanical Drilling Engine

Minimum Rating

440.0 bhp
Minimum Rating

440 BHP
Maximum Rating

595.0 bhp
Maximum Rating

595 BHP

Engine Specifications

Minimum Rating: 440.0 bhp
Minimum Rating: 440 BHP
Maximum Rating: 595.0 bhp
Maximum Rating: 595 BHP
Emissions: EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Emissions: EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Rated Speed: 2100.0 RPM
Rated Speed: 2100 r/min
Bore: 5.4 in
Bore: 5.4 in
Stroke: 6.75 in
Stroke: 6.75 in
Displacement: 928.0 in3
Displacement: 928 in³
Aspiration: Turbocharged-Aftercooled
Aspiration: Turbocharged-Aftercooled
Governor and Protection: ADEM A3
Engine Weight: 2743.0 lb
Engine Weight: 2743 lb
Oil Change Interval: 250
Rotation: Counterclockwise
Oil Change Interval: 250
Rotation from Flywheel End: Counterclockwise
Flywheel and Flywheel Housing: SAE No. 0 or SAE No. 1
Flywheel and Flywheel Housing: SAE No. 0 or SAE No. 1
Flywheel Teeth: 136 (SAE 0), 113 (SAE 1)
Flywheel Teeth: 136 (SAE 0), 113 (SAE 1)

Capacity for Liquids

Minimum Cooling System: 5.5 gal (US)

Dimensions

Length: 54.2 in
Length: 54 in
Width: 36.5 in
Width: 37 in
Height: 48.3 in
Height: 48 in

Air Inlet System
- Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature, pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
- Thermostats and housing — outlet vertical
- Jacket water pump — gear-driven, centrifugal, RH
- RH front water pump inlet
- All plugs/fittings are STOR for lines gp water
Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
- Full marmon connection, maximum load 10 kg for direct connection to turbo
Flywheels and Flywheel Housings
- See Mandatory Options
Fuel System
- MEUI system
- Fuel filter, secondary, mid-mount (LH 2 micron high performance)
- Fuel transfer pump, LH front
- Fuel priming pump, LH mid-mount
- Fuel sample valve, mounted on fuel filter base
Lube System
- Crankcase breather — rear valve cover
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — on oil filter base
Mounting System
- Front support (shipping only)
Power Take-Offs
- Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
- Hydraulic pump drive, SAE A, 11 tooth
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins, sockets)
- Literature group owner and operator
Mandatory Options
- Throttle position sensor
- Exhaust system — front or rear
- Flywheel housing or rear PTO
- Primary filter/water separator

Transmission Arrangement
- Transmission cooler
- Tool set
Air Compressor
- Air chambers
- Air compressor governor
Air Inlet System
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
Charging System
- Charging alternators
- Alternator mountings
- Alternator wiring
- Circuit breaker mountings
- Alternator belt guard
Cooling System
- Radiator — installed
- Radiator — ship loose
- Fan drive f/u/w Caterpillar installed radiator
- Fan drives for customer-supplied radiators
- Fan height instructions
- Vee belts for customer-supplied radiators
- Aftercooler lines f/u/w Caterpillar installed radiator
- Rear-facing exhaust
- Aftercooler lines
- Suction fan adapters — attaches fan to fan pulley
- Blower fan adapter — attaches fan to fan pulley
- Blower fan
- Suction fan
- Fan belt tightener
- Coolant level sensor
- Dry charge coolant conditioners
- Dry charge coolant conditioner element
Exhaust System
- Turbo exhaust connection
- Flexible fitting
- Elbows
- Flanges
- Dry elbow