New C15 ACERT™ Dry Manifold Engine for Sale

C15 ACERT™ Dry Manifold Engine

Maximum Rating

595 BHP
Displacement

928 in³
Minimum Rating

440 BHP
Governor and Protection

ADEM A3

General Specifications

Maximum Rating: 595 BHP
Displacement: 928 in³
Minimum Rating: 440 BHP
Governor and Protection: ADEM A3
Aspiration: Turbocharged-Aftercooled
Flywheel and Flywheel Housing: SAE No. 0 or SAE No. 1
Flywheel Teeth: 136 (SAE 0), 113 (SAE 1)
Rotation from Flywheel End: Counterclockwise
Stroke: 6.75 in
Bore: 5.4 in

Emissions

Emissions: EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Dimensions

Length: 54.2 in.
Length: 54 in
Width: 36.5 in.
Width: 37 in
Height: 48.3 in.
Height: 48 in
Weight: 2743.0 lb
Weight: 2743 lb

Capacity for Liquids

Cooling System: 5.5 gal (US)

Air Inlet System
- Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature, pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
- Thermostats and housing — outlet vertical
- Jacket water pump — gear-driven, centrifugal, RH
- RH front water pump inlet
- All plugs/fittings are STOR for lines gp water
Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
- Full marmon connection, maximum load 10 kg for direct connection to turbo
Flywheels and Flywheel Housings
- See Mandatory Options
Fuel System
- MEUI system
- Fuel filter, secondary, mid-mount (LH 2 micron high performance)
- Fuel transfer pump, LH front
- Fuel priming pump, LH mid-mount
- Fuel sample valve, mounted on fuel filter base
Lube System
- Crankcase breather — rear valve cover
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — on oil filter base
Mounting System
- Front support (shipping only)
Power Take-Offs
- Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
- Hydraulic pump drive, SAE A, 11 tooth
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins, sockets)
- Literature group owner and operator
Mandatory Options
- Throttle position sensor
- Exhaust system — front or rear
- Flywheel housing or rear PTO
- Primary filter/water separator

Transmission Arrangement
- Transmission cooler
- Tool set
Air Compressor
- Air chambers
- Air compressor governor
Air Inlet System
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
Charging System
- Charging alternators
- Alternator mountings
- Alternator wiring
- Circuit breaker mountings
- Alternator belt guard
Cooling System
- Radiator — installed
- Radiator — ship loose
- Fan drive f/u/w Caterpillar installed radiator
- Fan drives for customer-supplied radiators
- Fan height instructions
- Vee belts for customer-supplied radiators
- Aftercooler lines f/u/w Caterpillar installed radiator
- Rear-facing exhaust
- Aftercooler lines
- Suction fan adapters — attaches fan to fan pulley
- Blower fan adapter — attaches fan to fan pulley
- Blower fan
- Suction fan
- Fan belt tightener
- Coolant level sensor
- Dry charge coolant conditioners
- Dry charge coolant conditioner element
Exhaust System
- Turbo exhaust connection
- Flexible fitting
- Elbows
- Flanges
- Dry elbow