New C32 ACERT™ Dry Manifold Engine for Sale

C32 ACERT™ Dry Manifold Engine

Maximum Rating

1500 BHP
Displacement

1960.5 in³
Minimum Rating

800 BHP
Governor and Protection

ADEM A3

General Specifications

Maximum Rating: 1500 BHP
Displacement: 1960.5 in³
Minimum Rating: 800 BHP
Governor and Protection: ADEM A3
Aspiration: Turbocharged-Aftercooled
Flywheel and Flywheel Housing: SAE No. 0 or SAE No. 1
Flywheel Teeth: 136
Rotation from Flywheel End: Counterclockwise
Stroke: 6.4 in
Bore: 5.7 in

Emissions

Emissions: EPA and CARB Non-Road Mobile Tier 2, IMO Tier II, China Stage III

Dimensions

Length: 75.5 in.
Length: 76.18 in
Width: 58.0 in.
Width: 56.34 in
Height: 52.0 in.
Height: 54.66 in
Weight: 5040.0 lb
Weight: 5040 lb

Capacity for Liquids

Cooling System: 14.5 gal (US)

Air Inlet System
- Connections configured for ATAAC (Air-to-Air-Aftercooled) or remote heat exchanger
Control System
- ADEM A4 electronic control module
- Electronic governing, PTO speed control
- Customer programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Automatic fuel temperature compensation
- Programmable low and high idle, and top engine speed limit
- Electronic diagnostics and fault logging
- Engine monitoring system
- SAE J1939 broadcast (diagnostic and engine status)
Cooling System
- Gear-driven centrifugal jacket water pump — RH
- Integrated thermostat and housing
- Engine oil cooler
- Optional installed transmission oil cooler
Exhaust System
- Exhaust manifold — dry
- Two vertical exhaust outlets (front and rear)
Fuel System
- MEUI
- Fuel priming pump
- Fuel transfer pump
- Primary and secondary fuel filter — RH configured for remote mounting (installed RH on shipping plate)
Flywheels and Flywheel Housing
- SAE No. 0 or SAE No. 1 flywheel iron housing
- SAE No. 0 or SAE No. 1 flywheel
- Optional transmission adapter
Lube System
- Crankcase breather
- Oil filter — RH standard, optional LH or remote mount service
- Oil level gauge — RH standard, optional LH or dual service
- Oil filler — RH standard, optional LH or dual service
- Shallow oil pan, rear sump
Mounting System
- Trunnion front support
- Vertical and horizontal pads on rear flywheel housing
Protection System
- 24V electronic
- Engine overspeed with optional air shut-offs with indicators
- Low engine oil pressure
- Fuel filter restriction
- Fuel temperature
- High engine coolant temperature
- Low engine coolant temperature
General
- Vibration damper and optional guard
- Lifting eyes
- Optional customer wiring connector
- Service tool connector
- Paint — Cat yellow

Air Inlet System
- Air cleaner
- Air inlet adapters
- Turbocharger outlet adapters
- Air lines
Charging System
- Battery chargers
- Charging alternators
- Alternator mounting
- Circuit breakers and mountings
Cooling System
- Dry charge coolant conditioners
- Thermostat housing
- Coolant level sensor
- Radiator
- Blower fans
- Suction fans
- Fan adapters
- Fan drives
Emissions
- IMO certifications
Exhaust System
- Elbows
- Mufflers
Fuel Systems
- Electric fuel priming pump
Instrumentation
- Customer management device
- Interconnect harness
- Gauges and instrument panels
Lube System
- Oil pans
- Oil service side
- Oil level gauge
- Oil filters
- Lubricating oils
Mounting System
- Structural steel base
- Engine support — front
- Engine support — rear
Power Take-Offs
- Auxiliary drive
- Damper pulley
- Hydraulics gear pumps
Protection System
- Mechanical shutoffs
- Solenoid shutoffs
Starting System
- Electric starting motors - 12V, 24V
- Battery sets - 24V
- Battery cable
- Battery rack
- Starting aids
Transmission Arrangement
- Transmissions water lines
- Transmissions cooler