New C7 ACERT™ Dry Manifold Engine for Sale

C7 ACERT™ Dry Manifold Engine

Maximum Rating

300 BHP
Displacement

441.8 in³
Minimum Rating

225 BHP
Governor and Protection

Electronic (ADEM™ 3)

General Specifications

Maximum Rating: 300 BHP
Displacement: 441.8 in³
Minimum Rating: 225 BHP
Governor and Protection: Electronic (ADEM™ 3)
Aspiration: Turbocharged-Aftercooled
Flywheel and Flywheel Housing: SAE 1, 2, or 3
Flywheel Teeth: 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
Rotation from Flywheel End: Counterclockwise
Stroke: 5 in
Bore: 4.3 in

Emissions

Emissions: EPA & CARB Non-Road Tier 3, EU Stage IIIA, IMO Tier II

Dimensions

Length: 41.4 in.
Length: 41.4 in
Width: 29.9 in.
Width: 29.9 in
Height: 40.6 in.
Height: 40.6 in
Weight: 1386.0 lb
Weight: 1386 lb

Capacity for Liquids

Lube Oil System: 4.8 gal
Lube Oil System: 4.8 gal (US)

Air Inlet System
- Turbocharger, air to air aftercooled
- Air inlet, LH side facing front 79.0 mm (3.11 in) connection
Control System
- Electronic governing, PTO speed control
- Programmable rating
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speeds, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Automatic variable timing, electronic
- All engines shipped at max rated rpm
Cooling System
- Thermostats and housing, vertical outlet
- Jacket water pump — belt-driven, centrifugal
- Water pump, inlet RH front vertical inlet (pointing down)
Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
Fuel System
- Hydraulic Electronic Unit injection (HEUI)
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — LH front
- Fuel priming pump — LH front
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Electronic installation kit (connectors, pins, sockets)
Lube System
- Crankcase breather, LH side
- Oil cooler, RH
- Oil filler, front top valve cover
- Oil filter and sampling valve, RH
- Oil pan, front sump, 31 L (33 qt) oil change capacity
- Oil dipstick, LH rear
- Engine oil pump (gear-driven)
- Engine shipped without oil
Power Take-Offs
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide

Air Compressor
- Air compressors
- Air compressor governor
Air Inlet System
- Air cleaners
- Precleaner
- Air inlet elbow
- Air shutoffs
Charging Systems
- Charging alternators
- Alternator mountings
- Alternator belt tensioner
- Alternator pulleys
- Alternator guards
Cooling System
- Radiators
- Fan drive and pulley - f/u/w radiator packages
- Fans f/u/w radiator packages
- Coolant level sensor
- Fan drive mountings
- Fan adapters
- Fan adapter for blower fans
- Fan pulleys
- Fan height instructions
- Vee belts for customer-supplied radiators
- Suction fans and blower fans
- Water inlet elbows
- Dry charge coolant conditioners
Emissions Certification
- IMO Certification
Exhaust System
- Flexible fitting
- Turbocharger exhaust outlet adapters
- Elbows, flange, pipes, clamp
- Rain caps
- Manifolds
- Mufflers
Flywheels and Flywheel Housing
- Crankshaft seal
Fuel System
- Flexible fuel lines
- Water separator and fuel filters
- Fuel cooler
General
- Tool set
Instrumentation
- Gauges and instrument panels
- Interconnect harnesses
- Voltmeters
- Gauge mounting
- Ammeter
Lube System
- Oil pan
- Drain and cover
- Oil level gauges
- Remote oil filter
- Oil fillers
- Lubricating oil
- Fumes disposal
Mounting System
- Structural steel base
- Front engine support
- Rear engine supports
Power Take-Offs
- Enclosed clutch
- Clutch supports
- Flywheel stub shaft
- Hydraulic pump drives
- Hydraulic gear pumps
Starting System
- Starting Aids
- Electric Starting Motors — 12V and 24V
- Battery Sets - 12V and 24V (dry)
- Battery Cable