New C7 ACERT™ Hazardous Location Engine for Sale

C7 ACERT™ Hazardous Location Engine

Maximum Rating

275 BHP
Displacement

442 in³
Minimum Rating

205 BHP
Governor and Protection

Electronic ADEM™ A4

General Specifications

Maximum Rating: 275 BHP
Displacement: 442 in³
Minimum Rating: 205 BHP
Governor and Protection: Electronic ADEM™ A4
Aspiration: Turbocharged-Aftercooled
Flywheel and Flywheel Housing: SAE 1,2, or 3
Flywheel Teeth: 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
Rotation from Flywheel End: Counterclockwise
Stroke: 5 in
Bore: 4.3 in

Emissions

Emissions: EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II

Dimensions

Length: 4.38 in.
Length: 41.5 in
Width: 33.5 in.
Width: 29.8 in
Height: 43.8 in.
Height: 40.6 in
Weight: 1570.0 lb
Weight: 1386 lb

Capacity for Liquids

Lube Oil System: 36.0 gal
Lube Oil System: 36 gal (US)
Cooling System: 78.2 gal (US)

Air Inlet System
- Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Fuel cooled ECU
- Power compensation for fuel temperature
- Programmable low and high idle
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speed, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Certified electrical control system
- Derated engine: automatic ambient temperature compensation
Cooling System
- Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
- Jacket water pump — belt-driven, centrifugal
- Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
Exhaust System
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Exhaust manifold — water-cooled
- Front turbo exhaust
Flywheels and Flywheel Housing
- Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
Fuel System
- HEUI fuel system
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — left front
- Fuel priming pump — left front
Lube System
- Crankcase breather — top rear
- Crankcase fumes disposal — RH
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump, 31 L (33 qt) oil change capacity
- Oil filler — front top valve cover
- Oil level gauge — LH rear
- Engine oil pump — gear-driven
- Oil valve sampling, RH
Power Take-Offs
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
General
- Vibration damper
- Lifting eyes
- Literature
- No paint
Mandatory Options
- Flywheel housing and flywheel
- Primary filter/water separator
- Turbo orientation

Air Compressors
- Air compressor governor
Air Inlet System
- Precleaner
- Air inlet elbow
- Charging System
- Cooling System
Emissions Certifications
- IMO certification
Flywheels and Flywheel Housing
- Crankshaft seal
Instrumentation
- Gauges and instrument panels
Lube System
- Oil pans
- Drain and cover
- Remote oil filters
- Lubricating oils
Mounting System
- Structural steel base
- Engine support — front and rear
Power Take-Offs
- Rear enclosed clutches
- Hydraulic pump drives
- Crankshaft pulleys
General
- Tool set