Oil and Gas
CX35-P800 Oilfield Transmission
-
Gross Input Power800 BHP
-
Gross Input Power800 BHP
-
Gross Peak Input Torque2700 ft-lb
-
Gross Peak Input Torque2700 ft-lb
Transmission Specifications
- Gross Input Power
- 800 BHP
- Gross Input Power
- 800 BHP
- Gross Peak Input Torque
- 2700 ft-lb
- Gross Peak Input Torque
- 2700 ft-lb
- Rated Input Speed
- 2100 r/min
- Rated Input Speed
- 2100 r/min
- Maximum Turbine Torque
- 2700 ft-lb
- Maximum Turbine Torque
- 2700 ft-lb
- Minimum Input Speed
- 600 r/min
- Minimum Input Speed
- 600 r/min
- Electrical System
- 24 V
- Gear Type
- Planetary Spur
- Electrical System
- 24 V
- Gear Type
- Planetary Spur
- Gears
- 8F/1R
- Gears
- 8F/1R
- 1F Gear Ratio
- 5.73
- 1F Gear Ratio
- 5.73
- 2F Gear Ratio
- 3.57
- 2F Gear Ratio
- 3.57
- 3F Gear Ratio
- 2.72
- 3F Gear Ratio
- 2.72
- 4F Gear Ratio
- 1.95
- 4F Gear Ratio
- 1.95
- 5F Gear Ratio
- 1.43
- 5F Gear Ratio
- 1.43
- 6F Gear Ratio
- 1.00
- 6F Gear Ratio
- 1.00
- 7F Gear Ratio
- 0.74
- 7F Gear Ratio
- 0.74
- 8F Gear Ratio
- 0.63
- 8F Gear Ratio
- 0.63
- 1R Gear Ratio
- -4.46
- 1R Gear Ratio
- -4.46
- Overall Gear Ration
- 9.10
- Overall Gear Ration
- 9.10
- Overall Gear Ration
- 9.10
-
Cat Engines for Optimized Power Train
- C15 ACERT, C18 ACERT, and C27 ACERT (A ratings).
-
Transmission Rotation
- Input rotation — counterclockwise
- Output rotation — counterclockwise(as viewed from rear)
-
Torque Converter
- Lock-up clutch, torque converter drive in all gears integral to transmission
- Stall torque ratio - 1.962
-
Clutches
- Clutches — electro-hydraulic fully modulated, oil cooled, multidisc
- Clutch modulation control — Cat Electronic Clutch Pressure Control (ECPC)
-
Installation Connections
- 2 oil cooler lines
- 1 electrical connector
-
Oil System
- Cat Transmission/Drive Train Oil-4 (TDTO)
- Sump oil temperatures
- Maximum converter outlet oil temperature — 250°F (121°C)
- Hydraulic fill capacity — 9 gal (34 L), 16 gal 61L) initial fill
- Direct mount filter
-
Mountings
- Input (flywheel) — SAE #1 dry flywheel housing
- Side supports — two SAE #2 pads
- Output — 1810 yoke, 1810 companion flange, SPL 250 yoke, ISO 8667-T180 flange
-
Power Take-Off Drives
- Location
- Mounting type: 10 bolt
- Rated torque
- Rotation: same as engine
- Ratio, 1:1
-
Oil system
- Remote mount oil filter
-
Mountings
- Remote mount ECU
- Remote mount filter option
-
Integral Power Take-Off
- Location: 1 o'clock and 11 o'clock as viewed from rear
- Mounting type
- Rated torque
- Rotation: same as engine
- Ratio - 1:1
-
Rear Power Take-Off
- Location: 5 o'clock as viewed from rear
- Mounting type: 8 bolt (SAE pump adapters and drive flanges available from third party suppliers.
- Rated torque: 1000 lb-ft (1360 Nm)
- Rotation: Opposite of engine
- Ratio - 1.25:1
Buckets - Loader: 2.9m³ (3.75yd³) Material Handling Bucket for Wheel Loaders 
Buckets - Loader: 17.2 m³ (22.5 yd³) pin on Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 14.5 m³ (19 yd³) Fusion™ Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 14.5 m³ (19 yd³) pin on Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 14 m³ (18.25 yd³) pin on Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 11.9 m³ (15.5 yd³) Fusion™ Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 11.9 m³ (15.5 yd³) pin on Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 14 m³ (18.25 yd³) Fusion™ Light Material Bucket with Bolt-On Cutting Edge 
Buckets - Loader: 5.0 m3 (6.5 yd3) Pin On Light Material Bucket With Bolt-On Cutting Edge 
Buckets - Loader: 5.0 m3 (6.5 yd3) Pin On Light Material Bucket With Bolt-On Cutting Edge 
Buckets - Loader: 5.0 m3 (6.5 yd3) Fusion™ Light Material Bucket With Bolt-On Cutting Edge 
Buckets - Loader: 4.2 m3 (5.5 yd3) Fusion™ Light Material Bucket With Bolt-On Cutting Edge 
Buckets - Loader: 4.2 m3 (5.5 yd3) Pin On Light Material Bucket With Bolt-On Cutting Edge